|
|
| |
| 12 Volt Lights et al > Switches >
ICM-D1201 Rotary Dimmer Switch - Euro Style |
| |
Dimmer Switch
ICM-D1201: 12 Volt -24 Volt Dimmers - Easy to connect, 2 wire rotary dimmer
with built-in On-Off Switch for Halogen, Xenon, Incandescent Lights
|
Model ICM-D1201:
12 Volt Dimmer: 2 Wire, Rotary Dimmer
(Dimmer & On-Off
Switch).
Order below
The D1201 dimmers can be
used for incandescent, Halogen, or Xenon lights
(not fluorescent
lights not LED lights). NOTE: Due to the high start-up current drawn by halogen
and Xenon lamps, this dimmer may not be able to start 100 watts
of these types of bulbs. In this case, reduce the quantity or
wattage of bulbs in your circuit.
Colors: Available
in white, chrome , sandstone or brass color.
Great for new
installations & Great for Retrofits - easily replaces an
existing switch (install inline between 12 volt power source and
lights).
CE
marked |
|
ICM-D1201 - 12
Volt Dimmers
80 Watt, (rated at 100 watts, but
recommended
maximum load is 80 watts).
30 volts dc
max, power consumption 2mA max.
If you need a higher
power dimmer, refer to the
ILM Rotary Dimmers.
2.36" square bezel
(outside dimensions) -
see
diagram below for dimensions |
 |
|
|
|
|
|
1.
 |
12-24 Volt DC
Dimmer Switch,
White
Part Number:
ICM-D1201-WH
Suggested Retail
Price $66.00
now
$54.95
White is on
back-order until approximately September 8, 2008.
You may order and pay now to reserve yours.
Orders will ship on a first to order - first to ship
basis. |
|
|
 |
|
|
2.
 |
12-24 Volt DC
Dimmer Switch,
Chrome
Color
Part
Number: ICM-D1201-CR
Suggested Retail
Price $75.00
now $59.95 |
|
|
|
|
|
3.
 |
12-24 Volt DC
Dimmer Switch,
Sandstone
Part
Number: ICM-D1201-SS
Suggested Retail
Price $75.00
now $59.95 |
|
|
|
|
Looking
for matching Sandstone
color lights? See the
Ringo |
|
|
4.
 |
12-24 Volt DC
Dimmer Switch,
Brass
Color
Part Number: ICM-D1201-BR
Suggested Retail
Price $75.00
now $59.95 |
|
|
|
|
|
|
|
|
|
Mounting Suggestions:
|
|
2
Wire Dimmer ICM-D1201
-
New
installations:
Make a cutout for the 2.125" diameter housing directly
into your wall panel. Seat the housing into the wall cutout
and mark the wall for 4 pilot holes to match the housing
corner screw hole pattern. Remove the housing. Drill the
pilot holes in the wall. Wire the dimmer to your wiring in
the wall. Seat the dimmer housing into the wall cutout. Seat
the dimmer guts in the housing, pushing the excess wire into
the wall. Install 4 mounting screws to hold the housing to
the wall, and snap the bezel into place (this hides the
mounting screws).
-
To retrofit
into an existing switch housing, you may want to mount
the Dimmer D1201 onto a blank wall plate that fits
onto your existing switch housing (similar procedure to the
preceding paragraph).
Standard
Blank Wall plates that fit standard residential style
electrical switch boxes are available in various colors from
hardware stores and electrical suppliers.
|
Wiring
Diagram
Or 24 volts DC
(30 VDC Max) |
|
| |
|
Overview
Page of Switches and Dimmers |
| |
|
