|
|
| |
| 12
Volt Lights et al >
Rope
Lights > or
LED Rope Lights > Recommended Parts |
| |
3/8 Diameter
Rope Light Accessories - Page 1 of 3
Recommended Parts
|
|
|
| 1.
End Cap
- Recommended -
The End Cap protects the far end
of the wires that are embedded in the rope light from touching
anything they shouldn't. |
|
 |
| |
|
Part
Number: IMT-ILMDL-END
$0.29 each |
|
 |
|
|
2.
Power
Connection Options -
Recommended -
One of the
following Power Connection Options can be very useful with your
Incandescent
or LED
Rope Lighting. Choose carefully from the Power Connection
Options Chart below, to assure that you make the
appropriate choice. Warranty does NOT cover issues caused by
incorrect wiring on your part. If unsure, call us and/or hire a
licensed electrician. |
|
|
|
Power
Options 2A through 2E use various 6' Power Cord Kits. Each has a
connector assembly with pins that push into the end of the
rope light, making connection with the wires inside the
rope light jacket. A compression fitting is then tightened
to hold the Power Cord to the Rope Light, as shown below.
|
|
Rope
Light |
Compression Fitting |
Power Cord
Connector |
|
|
 |
|
|
Power Option 2F is
a compact connection
method for custom installations
by experts only: |
Power Option 2F |
|
Installation Note: LED rope lighting contains
diodes that allow the electricity to flow in one direction only.
Because of this, when you hook up power to the LED rope lighting,
it may not illuminate. If this is the case, disconnect the power
and reconnect it to the other end of the LED rope lighting. Before
you install your LED rope lights, connect the power and verify
illumination. Then as you do your installation, beware of which
end you need to feed the power to.
|
|
Power Option 2A:
6' AC Power Cord Kit for 3/8" diameter
For 110/120 Volt
AC Incandescent
Rope Lighting.
The plug is for use in a 110/120 VAC standard outlet.
The compression fitting attaches to the rope light as
shown above. Option 2C
(below) can also be used for 110/120 Volt AC Incandescent
Rope Lights. |
|
|
|
For 120 Volts AC used with
120 Volt Incandescent Rope Lights. |
Part Number:
IMT-ILMDL-CONKIT-6x120
MSRP $6.00
Now
$5.70 each |
|
|
|
|
Power Option 2B:
6' Power Cord Kit for 3/8" diameter
For 12 volt or 24
volt AC or DC powered Incandescent Rope Lighting
or
12 volt or 24 volt DC powered LED Rope Lighting.
Connect
the wire ends to the appropriate fused power source.
The compression fitting attaches to the rope light as
shown above. Option 2D
(below) can also be used for 12 Volt Incandescent Rope
Lights. Option 2E (below) can also be used for 24
Volt Incandescent Rope Lights. |
|
|
|
For 12 or 24 Volts AC or DC
used with 12 or 24 Volt Incandescent Rope Lights.
For 12 volts or 24 volts DC
used with 12 or 24 Volt LED Rope Lighting.
|
Part Number:
IMT-ILMDL-CONKIT-6x12/24
MSRP $6.00
Now
$5.70 each |
|
|
|
|
Power Option 2C:
6' Power Cord Kit for 3/8" diameter
For 110/120
volt AC powered LED Rope Lighting
or 110/120 volt
AC powered Incandescent Rope Lighting. USE THIS ITEM
IF YOUR POWER SOURCE IS A STANDARD
120 VAC OUTLET.
The compression fitting attaches to the rope light as
shown above. This item contains a rectifier. If the
rectifier is not used with LED Lights powered with an
AC source, they may flicker. This
item can also be used with 110/120 Volt Incandescent
Rope Lights. |
|
For 120 volts AC used
with
120 Volt LED Rope Lights. |
|
|
Part
Number:
IMT-ILMDL-CONKIT-L6
MSRP $6.75
Now
$6.42 each |
|
|
|
|
Power Option 2D:
6' Power Cord Kit for 3/8" diameter
12 volt AC
powered LED Rope Lighting or 12 volt AC powered
Incandescent Rope Lighting. USE THIS
ITEM IF YOUR POWER SOURCE IS A TRANSFORMER WITH A 12
VOLT AC OUTPUT.
Connect
the wire ends to the appropriate fused power source.
The compression fitting attaches to the rope light as
shown above. This item contains a rectifier. If the
rectifier is not used with LED Lights powered with an
AC source, they may flicker. |
|
For 12 volts AC
used with
12 Volt LED Rope Lights. |
Part
Number:
IMT-ILMDL-CON12V-L6
MSRP $6.75
Now
$6.42 each |
|
|
|
|
Power Option 2E:
6' Power Cord Kit for 3/8" diameter
For 24 volt
AC or DC powered LED Rope Lighting or 24 volt AC or DC
powered Incandescent Rope Lighting. USE THIS
ITEM IF YOUR POWER SOURCE IS A TRANSFORMER WITH A 24
VOLT AC OUTPUT.
Connect
the wire ends to the appropriate fused power source.
The compression fitting attaches to the rope light as
shown above. This item contains a rectifier. If the
rectifier is not used with LED Lights powered with an
AC source, they may flicker. |
|
For 24 volts AC
used with
24 Volt LED Rope Lights. |
Part
Number:
IMT-ILMDL-CON24V-L6
MSRP $6.75
Now
$6.42 each |
|
|
|
|
|
Power Option 2F:
Easy Splice Connector
- If
you are handy with a soldering iron, you may want to use
the "Easy Splice / Invisible Splice" connector to make a
compact, custom connection. This method should only be
used by persons with expert knowledge of electrical
systems. Use only with appropriate voltages and
corresponding rope lights. Note that LED lights may
flicker if powered by AC Voltage - A rectifier can
eliminate the flicker. This item does NOT contain a
rectifier. Review the following document: Wiring
Directly to Rope Light using an Easy Splice Connector |
|
|
|
|
Part Number:
IMT-ILMDL-INV
$1.67 each |
|
|
| |
|
|
|
|
Rope Light installation instructions
from the distributor (pdf file)
|
|
| |
|
Recommended Accessories
Mounting Methods
Splices & Splitters |
| |
| |
|
